纵向波纹隔热屏气膜冷却特性实验

针对加力燃烧室纵向波纹隔热屏气膜冷却效果开展了细致的实验研究,利用红外热像仪测量了隔热屏壁面的温度分布,分析了隔热屏板型、吹风比、开孔率等参数对气膜冷却效率的影响。实验中板型选取了平板和纵向波纹隔热屏,吹风比变化范围是0.5~3.0,开孔率变化范围是1.4%~3.7%。结果表明:相比于平板隔热屏的气膜冷却效率沿程逐渐增加,纵向波纹隔热屏的气膜冷却效率随波纹板的起伏而起伏且大于平板隔热屏;随着吹风比的增加气膜冷却效率逐渐加大,在吹风比为3.0时达到最大值;气膜冷却效率在波峰处低,波谷处高,整体上随波纹板的起伏而波动,吹风比越小,气膜冷却效率随波纹板的起伏变化越明显;高吹风比(吹风比为2.0~3.0)下,气膜冷却效率沿程变化与增幅较为缓慢;整体上,随着开孔率的增加气膜冷却效率逐渐加大,小开孔率(开孔率为1.4%、2.7%)下的气膜冷却效率相差不大,但在次流背风侧,开孔率小的气膜冷却效率要小于开孔率大的气膜冷却效率。      

一种开关磁阻电机无位置传感器控制效率优化策略

针对开关磁阻电机(SRM)的简化磁链法只能实现单相导通运行且导通区间固定的缺点,提出了一种结合固定关断角和自适应调节开通角的无位置传感器控制技术。利用曲线拟合关断位置磁链取代传统存储数据表,通过对比实时计算的动态磁链和曲线拟合的静态磁链,确定关断位置信号并估计转速和其他位置。考虑电机阻抗和电感的非线性特点,优化电感最小区域的开通角自调节模型确定导通区间。仿真结果验证了该方案的可行性和正确性,能够实现转子位置的间接检测,电机的运行效率得到进一步优化。     

对转压气机外伸激波对叶顶泄漏流影响

摘要:为了揭示对转压气机下游转子外伸激波对上游转子泄漏流的影响规律,针对上游转子叶顶间隙分别为0.2、0.5、0.8 mm的对转压气机开展了非定常数值模拟研究。研究发现:受下游转子外伸激波掠扫影响,上游转子尾缘附近压力面会形成弱压缩波,且随上游转子泄漏流增强而逐渐减弱;而该外伸激波在上游转子尾缘附近吸力面,会形成与型线切向相垂直的较强压缩波,且其位置基本不受叶顶间隙大小影响;外伸激波使上游转子尾缘附近吸、压力面压差增大,叶顶泄漏流增强,进而导致其损失增大;随着叶顶间隙增大,上游转子叶尖区弦长前半段压力波动的频率,由通道激波转为叶顶泄漏流主导,且呈现减小的趋势,而弦长后半段压力波动的频率主要由外伸激波主导,且基本不变。      

离心压缩机密封及空腔流动的一维/三维耦合建模研究

为了在保证数值预测精度的同时降低离心压缩机的建模复杂度,以一维密封泄漏计算替代完整的密封及空腔建模,开展了离心压缩机盖盘密封及空腔流动的源项建模方法研究。结果表明:基于源项方法的密封及空腔简化建模仅需在主流道建模基础上施加泄漏质量流量、总温和摩擦损失源项边界条件,即可较高精度地还原完整的盖盘密封及空腔建模的性能和关键流动细节。与完整建模相比,在全工况下源项建模预测的等熵效率的绝对偏差小于0.65%,总压比和等熵效率的相对性能偏差小于1%。该方法可在满足下游部件匹配设计精度需求的同时,减少50%以上的网格数量,并显著提高计算的经济性和收敛性。泄漏流量的计算精确度是影响源项建模法性能预测准确性的最关键因素,耦合建模可以采用一维计算中推荐的密封泄漏系数值。      

基于伴随方法的单级低速压气机气动设计优化

采用梯度方法对某型4.5级压气机最后级进行气动设计优化研究，梯度由连续伴随方法计算确定，多排伴随方程采用伴随掺混面模型进行数值求解。首先，采用基于经验修正的初步设计方法设计带进口导叶的4.5级低速、低压缩比压气机的原始气动外形。之后，在压气机近失速工况对最后级静子叶片进行伴随气动设计优化，通过优化叶型和安装角降低流动损失，目标函数定义为加权求和形式的熵增和流量偏差，优化中对流量进行约束。最后，开展基于伴随方法的多工况气动设计优化研究，改善两个不同转速条件下最后级的气动性能。优化结果表明，基于伴随方法的多排气动设计优化可以通过改变叶片气动外形提升多排全工况气动性能。     

Applications of structural efficiency assessment method on structural-mechanical characteristics integrated design in aero-engines

In the design process of advanced aero-engines, it is necessary to carry out an effective analysis method between structural features and mechanical characteristics for a better structural optimization. Based on the structural composition and functions of aero-engines, the concept and contents of structural efficiency can reflect the relation between structural features and mechanical characteristics. In order to achieve the integrated design of structural and mechanical characteristics, one quantitative analysis method called Structural Efficiency Assessment Method (SEAM) was put forward. The structural efficiency coefficient was obtained by synthesizing the parameters to quantitatively evaluate the aero-engine structure design level. Parameterization method to evaluate structural design quality was realized. After analyzing the structural features of an actual dual-rotor system in typical high bypass ratio turbofan engines, the mechanical characteristics and structural efficiency coefficient were calculated. Structural efficiency coefficient of high-pressure rotor (0.43) is higher than that of low-pressure rotor (0.29), which directly shows the performance of the former is better, there is room for improvement in structural design of the low-pressure rotor. Thus the direction of structural optimization was pointed out. The applications of SEAM shows that the method is operational and effective in the evaluation and improvement of structural design.     

扩压叶栅叶尖非定常流动的涡动力学机理

为了揭示压气机叶尖区旋涡结构与流动非定常性之间的关联，采用URANS对一亚声速平面扩压叶栅在不同攻角下的流场进行了求解，并借助Q判据提取了叶尖瞬态涡系结构。结果表明：泄漏涡的破碎现象能够通过诱导新的涡结构间接作用于相邻通道的叶尖流动，是导致叶尖流场失稳的关键因素。在-0.3°和+0.7°攻角下，叶尖泄漏涡发生了螺旋破碎，并伴随有非定常诱导涡的出现，诱导涡对相邻叶片载荷的影响使得叶尖泄漏涡发生周期性摆动；在+1.7°攻角下，泄漏涡破碎会导致反流涡的形成，反流涡的输运会给叶片载荷和来流攻角带来非定常扰动，反过来又会作用于泄漏涡的破碎和反流涡的生成，最终表现为一种自维持的非定常流动现象。     

基于MapReduce的CME参数识别模型并行计算技术

日冕物质抛射（Coronal Mass Ejection，CME）参数识别模型是太阳风预报过程的重要组成部分.在空间环境预报业务中，为提高太阳风预报的准确率，需要提高CME参数识别的精度.模型以计算任务串行的方式运行，运算效率低导致模型运算时间长，不能满足这种需求.CME参数识别模型的物理运算过程相互不独立，其在单节点上的运行方式不能满足并行化要求.基于MapReduce的并行计算框架，改进了CME参数识别模型的计算流程，提出CDMR（CME detection under MapReduce）方法，实现了CME参数识别模型的并行计算，并对比分析CME参数识别模型在串行计算和MapReduce并行计算下的运行时间，提高了模型的识别精度和计算效率.      

Flow mechanism between purge flow and mainstream in different turbine rim seal configurations

The rim seal is used to prevent mainstream ingestion to the gap between the vane of a turbine and its blade. In this article, the dolphin lip with a hook configuration and a large seal cavity with hook structures are designed based on the high-pressure turbine datum single shark lip rim seal configuration. The sealing effect and parameters of the flow field are measured by an experiment method and a numerical simulation is used to explain the mechanism. For three configurations, the effect of the leakage slot vortex on the efficiency of the seal and the influence of leakage vortex, generated by the interaction between purge flow and mainstream flow, are discussed in depth. The result shows that the reverse vortex formed by the dolphin lip rim seal with hook structure will increase the sealing efficiency. The seal configuration with a large cavity improves sealing efficiency to a greater extent than the datum structure. At different purge flow rates and with unequal seal structures, the purge flow produces three types of leakage vortices in the passage. Besides, the seal configuration with dolphin lip produces a Kelvin-Helmholtz instability at the interface of the purge and the mainstream flows at a low purge flow rate to induce new leakage vortex branches in the passage of the blade.     

新型主减隔振装置隔振性能测试试验研究

为解决新研全尺寸主减隔振装置地面性能试验中由于试验件尺寸大、重量重和试验状态多等难点,同时缩短试验周期并降低试验成本,提出了一种通过实测动载荷传递率评估主减隔振装置隔振性能的地面性能试验方法,给出了试验方案、试验夹具安装、试验内容以及过程。通过理论分析和试验结果,验证了实测动载荷传递率试验方案的可行性,测试结果真实可靠,为后续类似的系统级全尺寸隔振性能试验提供了一种新的试验方法。试验结果表明:新型主减隔振装置对垂向、航向和侧向三向激励的隔振效率均超过了80%,达到了预期的减振效果。